Showing results: 661 - 675 of 1086 items found.
-
Compliance West USA, Inc
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
N19303B -
Keysight Technologies
The new Physical Layer Test System (PLTS) 2024 is the industry standard for signal integrity measurements and data post‑processing high-speed interconnects, such as cables, backplanes, PCBs, and connectors. Signal integrity laboratories worldwide have benefited from the power of PLTS in the R&D prototype test phase.
-
A694 -
AGM Elettronica
The A694 is a short circuit locator designed for fault location in metallic cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A694 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 0.1 ohm and less than 40 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
RFCT -
Textron Systems
Textron Systems’ Radio Frequency Cable Tester (RFCT) allows for on-site testing and maintenance for radio frequency (RF) transmission paths within a platform. Using preconfigured databases of sweep parameters and pass/fail criteria, the RFCT quickly determines the status of installed RF cables. The RFCT checks each cable’s performance characteristics to include voltage standing wave ratio (VSWR), insertion loss (IL), phase and phase matching. If a cable fails a test, the RFCT automatically determines the distance-to-fault (DTF). With its intuitive touchscreen-based user interface and lightweight, ruggedized packaging, the RFCT is the gold standard for operational-level RF cable testing.
-
OS430 -
Advanced Fiber Solutions
The OS430 Laser source is for single-mode fibers in the outside plant environment where the long wavelengths are used. The Single output allows the user to test at both 1310nm and 1550nm without disconnecting and reconnecting the cable.
-
MDTH series -
Microwave Factory Co,Ltd.
This product is the antenna that corresponds to the radar pulse immunity test for automotive equipments. Automotive manufacturers have required the electric field strength of 600 v/m. Amplifier system and cable will be cheaper, and will contribute to the ecology.
-
CX-G13 -
Shenzhen Chuangxin Instruments Co., Ltd.
Tumbling Barrel Tester The Tumbling Barrel Test simulates repeated falls which may occur to such devices as connectors or small remote control units which are normally attached to cables during use.
-
Teledyne LeCroy
The Teledyne LeCroy WavePulser 40iX and the Teledyne Test Tools T3SP15D are a perfect combination of complimentary products to serve the requirements on testing, validating and troubleshooting cables, backplanes, connectors, transmission lines on boards and interconnect.
-
LAN & Breaker -
Amprobe Test Tools
Find opens, shorts and mis-wired cable installations with quick go/no-go tests, using an Amprobe LAN tester. Identifying circuit breakers is efficient when you use an Amprobe breaker tracer.
-
Teledyne Defense Electronics Storm Microwave
We’ve been the gold standard in test cables for decades. The table below shows how our different families compare. Entries further down the page are generally higher performance, higher cost.
-
N1420A -
Keysight Technologies
The N1420A is optional software to compare, evaluate and record noise from test setup. It is helpful when you isolate the cause of noise related to setup elements such as cables, connectors, shields, chambers, etc.
-
TA-60 -
Tech-Aid Products
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
SCR ELEKTRONIKS
SCR ELEKTRONIKS focuses on designing a solution around the end use at her customer. Instead of offering a standard instrument for a specific task, we have an approach of customizing the test bench to target the specific goals of the process or test procedure. Our measurement instruments, test modules, electrical power systems & software libraries are developed with this vision, thereby reducing the test system’s time-to-deploy. Cord Grip Test Apparatus for testing effectiveness of the retention in flexible cables.
-
Easy Touch -
Cirris Systems Corporation
Test all your cable or harness designs quickly and confidently with our newest cable and harness tester. EasyTouch checks for opens, shorts, and miswires and performs IR/DWV testing up to 2000Vdc (1000VAC Optional). Easy Touch features an integrated Windows 7 PC complete with hard drive, VGA, USB, Ethernet, and audio ports and a large 10.4" graphical touch-screen display.
-
OTDR Sidekick -
M2 Optics, Inc.
Intended to eliminate the "dead zone" at the beginning of a fiber cable when using an OTDR, The Sidekick from M2 Optics is a compact, durable solution for both field and laboratory use. Commonly referred to as a launch box, pulse suppressor, or launch cable, this durable test box is also used as a fiber optic delay line and for a variety of other short-distance testing and training applications.